Water Magnetic Flowmeter Digital Display Water Pump Liquid Electromagnetic Flow Meter

With the speeding up of urbanization process in our country, environmental pollution is increasingly serious. Because in sewage treatment, it is necessary to analyze and control the discharged sewage, additives, sludge, etc., so the flow measurement is very important. Among the many flowmeter products used for sewage measurement, electromagnetic flowmeter measurement accuracy is higher.

Electromagnetic flowmeters find applications in numerous industries due to their adaptability and precision. They are extensively used in water and wastewater management for monitoring water distribution, sewage treatment, and environmental compliance. In chemical and petrochemical industries, these flowmeters excel in measuring the flow of corrosive and abrasive liquids. The food and beverage sector benefits from their accuracy in ensuring consistent liquid measurements during production processes. In pharmaceutical manufacturing, electromagnetic flowmeters contribute to the precise control of liquid ingredients, while in mining and minerals processing, they help optimize the efficiency of slurry flow.

Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s
Conductivity: >5us/cm
Protection Class: IP65(Standard); IP68(Optional for remote type)
Process Connection: Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal: 4-20mA/Pulse
Communication: RS485(Standard), HART(Optional),GPRS/GSM (Optional)

What are the problems encountered when electromagnetic flowmeters are used in paper mills

Several factors can contribute to the inaccurate measurement of flow by electromagnetic flowmeters. These factors can vary depending on the specific application, installation conditions, and characteristics of the fluid being measured. Here are some common reasons for inaccurate flow measurement with electromagnetic flowmeters:

Intelligent electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including acid, alkali, salt and other highly corrosive liquids.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Proper installation of electromagnetic flowmeters is crucial to ensure accurate and reliable measurement of fluid flow in various industrial applications. The first step in the installation process involves selecting an appropriate location for the flowmeter. It is essential to place the flowmeter in a section of the piping system where the flow profile is stable, avoiding areas with turbulence, elbows, or other disturbances that may affect the accuracy of measurements. Additionally, the installation site should provide easy access for maintenance and calibration activities.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

The material of construction is also a vital aspect in electromagnetic flowmeter selection. Different applications may require flowmeters made from specific materials to withstand corrosive environments or harsh chemicals. Ensuring that the materials of construction are compatible with the fluid and environmental conditions helps enhance the longevity and reliability of the flowmeter.

Another critical factor to consider is the flow rate range of the application. Electromagnetic flowmeters exhibit excellent accuracy and stability across a broad range of flow rates, making them suitable for both low-flow and high-flow applications. It is essential to match the flowmeter’s specifications, such as its minimum and maximum flow rates, with the expected flow conditions in the system.

Measuring Range： Max 15m/s
Conductivity： >5us/cm
Protection Class： IP65(Standard); IP68(Optional for remote type)
Process Connection： Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal： 4-20mA/Pulse
Communication： RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply： AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption： <20W Alarm： Upper Limit Alarm / Lower Limit Alarm Self-diagnosis： Empty Pipe Alarm, Exciting Alarm Explosion Proof： ATEX

One of the defining features of electromagnetic flowmeters is their exceptional precision and accuracy in measuring fluid flow rates. The utilization of Faraday’s law of electromagnetic induction ensures that the induced voltage is directly proportional to the flow rate of the conductive liquid passing through the magnetic field. This inherent accuracy makes electromagnetic flowmeters a go-to choice in applications where precise measurements are critical, such as in pharmaceutical manufacturing, chemical processing, and water treatment.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa… Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s
Conductivity: >5us/cm

In addition to signal analysis, real-time monitoring is a crucial aspect of fault diagnosis for electromagnetic flow meters. Continuous assessment of key parameters, such as fluid conductivity and temperature, can help detect anomalies that may impact meter accuracy. For instance, sudden changes in conductivity might signal issues like fluid contamination or changes in fluid composition, prompting the need for further investigation.

Electromagnetic water meters offer several advantages in water measurement applications, particularly in industrial and municipal settings. Here are some key advantages of electromagnetic water meters:

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

The requirements of the straight tube section of the electromagnetic flowmeter are very important to ensure the accuracy and stability of the measurement results. The following is a detailed analysis of the requirements of the straight pipe section before and after the electromagnetic flowmeter:

The working principle of electromagnetic flow meter:

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Electromagnetic flowmeter is a speed meter to measure the volume flow of conductive media. While carrying out on-site monitoring and display, it can output standard current signals for recording, adjustment and control, realizing automatic control of detection, and realizing long-distance transmission of signals. It can be widely used in water, chemical, coal, environmental protection, textile, metallurgy, paper and other industries in the flow measurement of conductive liquid. The structure of the instrument has one type and one type.

Performance Technical parameter
Size DN3-DN3000mm
Nominal Pressure 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy +/-0.5%(Standard)     +/-0.3% or +/-0.2%(Optional)
Liner PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode SUS316L, Hastelloy B, Hastelloy C       Titanium, Tantalum, Platinium-iridium
Structure Type Integral type, remote type, submersible type, ex-proof type
Medium Temperature -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature -20~+60deg C
Ambient Humidity 5-100%RH(relative humidity)
Measuring Range Max 15m/s
Conductivity >5us/cm
Protection Class IP65(Standard); IP68(Optional for remote type)
Process Connection Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal 4-20mA/Pulse
Communication RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption <20W Alarm Upper Limit Alarm / Lower Limit Alarm Self-diagnosis Empty Pipe Alarm, Exciting Alarm Explosion Proof ATEX

Drainage flowmeter, sewage outfall flowmeter installation position

Electromagnetic flowmeters, also known as magmeters or magnetic flowmeters, are widely used for measuring the flow rate of conductive liquids in various industries. Several factors can influence the accuracy of electromagnetic flowmeters. Understanding and addressing these factors are essential to ensure precise and reliable flow measurements. Here are some key factors that can affect the accuracy of electromagnetic flowmeters:

Electromagnetic flow meters operate based on a fundamental principle of electromagnetic induction, providing an accurate and reliable method for measuring the flow of conductive fluids. The working principle involves Faraday’s law of electromagnetic induction. As a conductive fluid flows through a pipe, it cuts across the magnetic field generated by coils or electrodes mounted on the flow meter. According to Faraday’s law, an electromotive force (EMF) is induced in the fluid perpendicular to both the magnetic field and the flow direction. The induced EMF is directly proportional to the flow velocity of the fluid.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Electromagnetic flowmeters, also known as magmeters, are widely used in various industries for measuring the flow rate of conductive fluids. They operate based on Faraday’s law of electromagnetic induction, where a voltage is induced in a conductor (the fluid) as it moves through a magnetic field. These flowmeters are favored for their accuracy, reliability, and suitability for a wide range of applications. Here are different categories of electromagnetic flowmeters and their fields of application:

The electrode is the main part of the electromagnetic flowmeter used to measure the liquid flow, therefore, the choice of normal electrode material is directly related to the accuracy of the measurement and the price of the electromagnetic flowmeter.

The role of electromagnetic flow meter grounding in actual installation. Compared with other flowmeter products, electromagnetic flowmeter has high precision, reliable performance, stable work and excellent anti-interference ability. However, as a precision instrument, in order to meet these high requirements, it is necessary to have strict installation requirements, this article will introduce the electromagnetic flowmeter grounding wire that is often not paid attention to when installing.

Electromagnetic flow meters offer several advantages, making them a popular choice in various industrial applications. Here are some of the key advantages of electromagnetic flow meters:

The correct selection of electromagnetic flowmeter is the prerequisite to ensure the normal use of the instrument. The diameter, flow range, lining material, electrode material and output current of the electromagnetic flowmeter should be determined according to the physical and chemical properties of the measured flow medium, and can adapt to the field environment and meet the technical indicators and performance requirements.

Electromagnetic flowmeter is widely used in the industrial field, in order to make the electromagnetic flowmeter work stable and reliable, accurate measurement, installation needs to be installed in accordance with the correct method.

Selecting the appropriate installation point for an electromagnetic flowmeter is crucial for accurate and reliable measurements. Here are some considerations and guidelines to help you choose the right measuring installation point: