Tri Clamp Water Flow Sensors RS485 Milk Flowmeter Electromagnetic Sanitary Flow Meter

What fault will occur during the debugging period of the plug-in electromagnetic flowmeter, the split electromagnetic flowmeter and the initial debugging fault, but once the fault is improved, it will generally not occur again under the same conditions.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

The transducer in the split electromagnetic flowmeter can form a body or separate type with the sensor, the integrated electromagnetic flowmeter is the integrated electromagnetic flowmeter, the split type becomes the split electromagnetic flowmeter, the flowmeter is a two-way measurement system, and the three integrators are installed: the forward total, the reverse total and the difference total

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Due to various reasons, some large diameter flowmeters used online can not be tested off-line. It has become an urgent problem to study an online calibration method which is both scientific and effective and ADAPTS to the needs of the field. At present, there are three common methods for online calibration of electromagnetic flowmeters:

The measuring accuracy and stability of the electromagnetic flowmeter is directly related to whether the electromagnetic flowmeter housing is grounded.

What are the advantages of electromagnetic flowmeter measurement for sewage measurement? The plug-in electromagnetic flowmeter is composed of two parts: flow sensor and transmitter.

Usually there is more or less a mixture in the fluid in the measurement of some occasions. In general, in the presence of a small bubbling flow of oil and gas bubbles, it is still able to work normally, but the measurement is a fusion of the volume of oil bubbles, if the proportion of oil and gas rises to have caused a projectile flow, then the electrode may be covered by gas, resulting in the circuit is disconnected, the output shake is more likely to be directly damaged.

When using electromagnetic flowmeters in the field, it’s important to perform regular checks and maintenance to ensure accurate and reliable flow measurements. Here are some key parameters to check and consider in the field for electromagnetic flowmeter use:

1. The role of the electromagnetic flowmeter grounding ring: the grounding ring is directly in contact with the medium through the grounding electrode, and then grounded with the flange of the electromagnetic flowmeter through the grounding ring to achieve equal potential with the ground to eliminate interference.

The ability of electromagnetic flowmeters to provide real-time data on fluid flow rates is a key performance aspect. Industries benefit from the immediate and accurate insights into their processes, allowing for proactive monitoring and control. This feature is especially crucial in applications such as water distribution networks, where real-time data facilitates efficient resource management and timely responses to changes in flow conditions.

Measuring Range: Max 15m/s
Conductivity: >5us/cm
Protection Class: IP65(Standard); IP68(Optional for remote type)
Process Connection: Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal: 4-20mA/Pulse
Communication: RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply: AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption: <20W Alarm: Upper Limit Alarm / Lower Limit Alarm Self-diagnosis: Empty Pipe Alarm, Exciting Alarm Explosion Proof: ATEX

Intelligent electromagnetic flowmeter has a pivotal position in liquid measurement with high measurement accuracy and stable performance. It can be seen everywhere, today we mainly talk about the intelligent electromagnetic flowmeter in daily use, which parts – electrode related maintenance points:

Electromagnetic flowmeter is a speed meter to measure the volume flow of conductive media. While carrying out on-site monitoring and display, it can output standard current signals for recording, adjustment and control, realizing automatic control of detection, and realizing long-distance transmission of signals. It can be widely used in water, chemical, coal, environmental protection, textile, metallurgy, paper and other industries in the flow measurement of conductive liquid. The structure of the instrument has one type and one type.

Performance Technical parameter
Size DN3-DN3000mm
Nominal Pressure 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy +/-0.5%(Standard)     +/-0.3% or +/-0.2%(Optional)
Liner PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode SUS316L, Hastelloy B, Hastelloy C       Titanium, Tantalum, Platinium-iridium
Structure Type Integral type, remote type, submersible type, ex-proof type
Medium Temperature -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature -20~+60deg C
Ambient Humidity 5-100%RH(relative humidity)
Measuring Range Max 15m/s
Conductivity >5us/cm
Protection Class IP65(Standard); IP68(Optional for remote type)
Process Connection Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal 4-20mA/Pulse
Communication RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption <20W Alarm Upper Limit Alarm / Lower Limit Alarm Self-diagnosis Empty Pipe Alarm, Exciting Alarm Explosion Proof ATEX

Drainage flowmeter, sewage outfall flowmeter installation position

Electromagnetic flowmeter in the use process will produce some faults affect the normal work of the instrument, how to find the cause behind the fault is a very important work, we need to identify through a variety of different types of detection methods, in general, we for electromagnetic flowmeter routine testing, usually including electrode contact resistance, electrode polarization voltage, Signal cable interference, the determination of whether there is a grounding potential and the flow of stray current in the pipeline five aspects, these five aspects can be carried out separately, in fact, but also interrelated, any change in the factor may cause other changes, this reminds everyone in the detection of special attention:

The working principle of electromagnetic flow meter:

The electrode is the main part of the electromagnetic flowmeter used to measure the liquid flow, therefore, the choice of normal electrode material is directly related to the accuracy of the measurement and the price of the electromagnetic flowmeter.

Electromagnetic flow meters offer several advantages, making them a popular choice in various industrial applications. Here are some of the key advantages of electromagnetic flow meters:

Advantages and disadvantages of electromagnetic flowmeter

The performance excellence of electromagnetic flowmeters is further underscored by their low maintenance requirements. The absence of mechanical components in direct contact with the fluid minimizes wear and tear, reducing the need for frequent maintenance interventions. This not only enhances the longevity of the flowmeter but also translates into cost savings for industries where operational efficiency is paramount.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa… Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Four physical cleaning methods of electromagnetic flowmeter electrode

Selection of lining materials for electromagnetic flowmeter

Electromagnetic flow meters offer several advantages, making them a popular choice in various industrial applications. Here are some of the key advantages of electromagnetic flow meters:

How to correctly select the installation point of the electromagnetic flowmeter

The selection of circulating water flowmeter is a decision process involving many aspects, which needs to consider the characteristics of circulating water, measurement requirements, environmental conditions, economic costs and the performance characteristics of the flowmeter. Here is a comprehensive analysis and recommendations for the best options:

Electromagnetic flow meters, also known as magmeters, are advanced devices used for measuring the flow rate of conductive fluids such as water and slurries. These meters operate based on the principles of electromagnetic induction. A magnetic field is generated by the meter’s coils, and as the conductive fluid flows through the meter’s pipe, it generates a voltage proportional to the flow rate. The strength of this induced voltage is directly correlated with the speed of the fluid, allowing for accurate and reliable flow measurements.

Electromagnetic flowmeters, commonly known as magmeters, are a sophisticated and versatile type of flow measurement device widely used in industrial applications. Unlike traditional mechanical flow meters, electromagnetic flowmeters operate on the principle of electromagnetic induction to provide highly accurate and reliable measurements of liquid flow. The technology behind these devices makes them suitable for a diverse range of industries where precise flow measurement is crucial for various processes.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Electromagnetic flowmeters, also known as magmeters or magnetic flowmeters, are widely used for measuring the flow rate of conductive liquids in various industries. Several factors can influence the accuracy of electromagnetic flowmeters. Understanding and addressing these factors are essential to ensure precise and reliable flow measurements. Here are some key factors that can affect the accuracy of electromagnetic flowmeters: