water flow meter

Vortex flowmeter is widely used because of its wide range, small pressure loss, medium accuracy, linear output, no moving parts, high reliability, small maintenance, medium low price, relatively high performance and price characteristics.

Liquid turbine flowmeter mainly uses advanced single-chip microcomputer technology, is a new type of flow meter and traditional turbine flow sensor and secondary meter measurement system, compared with its smaller volume, and intuitive reading display, turbine flowmeter in the measurement, will not be affected by external power supply, and has a good anti-lightning meter low cost advantage.

As a measuring device with simple structure, sensitive response and not affected by physical properties such as temperature and viscosity of the measured medium, electromagnetic flowmeter has been widely used in the water supply industry, and has obtained good results.

The choice of water flow meter is a comprehensive consideration process, involving many aspects of factors. Here is a guide to tap water flow meter selection to help you choose the most suitable solution:

The scale of the water supply system itself is huge, and the environment in which it is located is complex and changeable, requiring the electromagnetic flowmeter to have strong stability and reliability, so in the actual use process, the matters needing attention should be clear.

Electromagnetic flowmeters can achieve remote communication through various digital communication protocols. These protocols allow flowmeter data to be transmitted to remote monitoring systems, control rooms, or other devices for real-time monitoring, analysis, and control. Some common digital communication protocols used for remote communication with electromagnetic flowmeters include:

When measuring waste acid using an electromagnetic flowmeter, it’s crucial to choose electrodes that are suitable for the corrosive nature of the acid and that can withstand the specific conditions of the application. Common electrode materials for electromagnetic flowmeters used in corrosive environments include:

The installation distance between an electromagnetic flowmeter and a control valve, especially a rear valve, is a critical factor that can impact the accuracy and reliability of flow measurements. Here are some general guidelines to help determine the appropriate installation distance:

The electromagnetic flow meter consists of a non-conductive pipe lined with a conductive material, typically made of metal. The meter contains coils or electrodes positioned opposite each other on the pipe’s inner walls. A magnetic field is then generated by passing a current through these coils, creating a measurable voltage across the fluid. The induced voltage, or EMF, is directly proportional to the fluid’s velocity, allowing the flow meter to accurately determine the flow rate. Importantly, this principle remains effective regardless of the fluid’s conductivity, making electromagnetic flow meters suitable for a wide range of applications, including water, wastewater, and various industrial processes.

Electromagnetic flowmeters, also known as magmeters, are devices that measure the flow of electrically conductive fluids using the principles of electromagnetic induction. There are several types of electromagnetic flowmeters, each with its own characteristics and applications. Here are some common types:

Electromagnetic flowmeters, also known as magmeters, are devices that measure the flow of electrically conductive fluids using the principles of electromagnetic induction. There are several types of electromagnetic flowmeters, each with its own characteristics and applications. Here are some common types:

Calibration checks are another essential component of fault diagnosis for electromagnetic flow meters. Regular calibration against known standards ensures that the meter’s measurements remain accurate over time. Any deviation from the expected calibration values may indicate sensor degradation, electronic component failure, or other issues that require attention.

Electromagnetic flow meters, like any complex instrumentation, require effective fault diagnosis methods to ensure their optimal performance and reliability. One common approach to diagnosing issues with electromagnetic flow meters involves the analysis of the sensor signals. Any deviation from the expected output can be indicative of potential problems within the system. Advanced diagnostic algorithms can be employed to detect abnormalities in the induced voltage or electromagnetic field, allowing for the identification of faults such as sensor drift, signal noise, or electrode fouling.

In industrial settings, electromagnetic flow meters play a vital role in process control and monitoring. Their ability to provide accurate measurements in challenging conditions, such as high temperatures and abrasive environments, makes them indispensable for industries like water treatment, chemical processing, and wastewater management. The continuous advancements in technology have further enhanced the capabilities of electromagnetic flow meters, making them a trusted and widely adopted solution for precise flow measurement in diverse applications.

Electromagnetic flow meters, also known as magmeters, are advanced devices used for measuring the flow rate of conductive fluids such as water and slurries. These meters operate based on the principles of electromagnetic induction. A magnetic field is generated by the meter’s coils, and as the conductive fluid flows through the meter’s pipe, it generates a voltage proportional to the flow rate. The strength of this induced voltage is directly correlated with the speed of the fluid, allowing for accurate and reliable flow measurements.

Selecting the appropriate installation point for an electromagnetic flowmeter is crucial for accurate and reliable measurements. Here are some considerations and guidelines to help you choose the right measuring installation point:

Another notable characteristic of liquid turbine flowmeters is their wide rangeability. These flowmeters can effectively measure a broad spectrum of flow rates, from low to high, while maintaining consistent accuracy. This versatility is crucial in industries where liquid flow rates can vary significantly, allowing for the measurement of different flow conditions without sacrificing measurement precision.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Liquid turbine flowmeters also find application in the pharmaceutical industry, where precise measurements of liquid flow rates are vital for the production of pharmaceutical products. From monitoring the flow of ingredients during manufacturing to ensuring accurate dosing in pharmaceutical research and development, these flowmeters contribute to the quality and consistency of pharmaceutical processes.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Proper installation of electromagnetic flowmeters is crucial to ensure accurate and reliable measurement of fluid flow in various industrial applications. The first step in the installation process involves selecting an appropriate location for the flowmeter. It is essential to place the flowmeter in a section of the piping system where the flow profile is stable, avoiding areas with turbulence, elbows, or other disturbances that may affect the accuracy of measurements. Additionally, the installation site should provide easy access for maintenance and calibration activities.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

electromagnetic flowmeters have a wide range of applications across diverse industries, addressing the need for accurate and efficient fluid flow measurement in fields as varied as water management, industrial processes, energy production, environmental monitoring, and HVAC systems. Their adaptability and reliability make them indispensable tools in ensuring precise fluid flow measurements for improved process control and operational performance.

Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range： Max 15m/s
Conductivity： >5us/cm
Protection Class： IP65(Standard); IP68(Optional for remote type)
Process Connection： Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal： 4-20mA/Pulse
Communication： RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply： AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)

Size DN3-DN3000mm
Nominal Pressure 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA

Electromagnetic water meters offer several advantages in water measurement applications, particularly in industrial and municipal settings. Here are some key advantages of electromagnetic water meters:

Liquid turbine flow meters are devices used to measure the flow of liquids through a pipeline. They operate on the principle of a turbine rotor turning in response to fluid flow. Here are some advantages of liquid turbine flow meters:

Electromagnetic flow meters offer several advantages, making them a popular choice in various industrial applications. Here are some of the key advantages of electromagnetic flow meters:

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s