Stainless Steel 4-20mA Digital Liquid Control Electromagnetic Flow Meter Water Magnetic Flowmeter

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Drainage flowmeter, sewage outfall flowmeter installation position

When using electromagnetic flowmeters in the field, it’s important to perform regular checks and maintenance to ensure accurate and reliable flow measurements. Here are some key parameters to check and consider in the field for electromagnetic flowmeter use:

The role of electromagnetic flow meter grounding in actual installation. Compared with other flowmeter products, electromagnetic flowmeter has high precision, reliable performance, stable work and excellent anti-interference ability. However, as a precision instrument, in order to meet these high requirements, it is necessary to have strict installation requirements, this article will introduce the electromagnetic flowmeter grounding wire that is often not paid attention to when installing.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Electromagnetic flowmeters find versatile applications across various industries due to their precision and reliability in measuring fluid flow. One primary area of application is in water and wastewater management, where these flowmeters excel in accurately measuring the flow of water and other conductive fluids. Municipalities and water treatment plants utilize electromagnetic flowmeters to monitor water distribution networks, optimize usage, and ensure efficient wastewater processing.

Measuring Range： Max 15m/s
Conductivity： >5us/cm
Protection Class： IP65(Standard); IP68(Optional for remote type)
Process Connection： Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal： 4-20mA/Pulse
Communication： RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply： AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption： <20W Alarm： Upper Limit Alarm / Lower Limit Alarm Self-diagnosis： Empty Pipe Alarm, Exciting Alarm Explosion Proof： ATEX

Electromagnetic flowmeter in the use process will produce some faults affect the normal work of the instrument, how to find the cause behind the fault is a very important work, we need to identify through a variety of different types of detection methods, in general, we for electromagnetic flowmeter routine testing, usually including electrode contact resistance, electrode polarization voltage, Signal cable interference, the determination of whether there is a grounding potential and the flow of stray current in the pipeline five aspects, these five aspects can be carried out separately, in fact, but also interrelated, any change in the factor may cause other changes, this reminds everyone in the detection of special attention:

Electromagnetic flowmeters, also known as magmeters, are devices that measure the flow of electrically conductive fluids using the principles of electromagnetic induction. There are several types of electromagnetic flowmeters, each with its own characteristics and applications. Here are some common types:

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Electromagnetic flowmeters are used to measure the volume flow of industrial liquids and there are many media in industrial liquids, electromagnetic flowmeters are often used to measure the flow of conductive media.

The correct selection of electromagnetic flowmeter is the prerequisite to ensure the normal use of the instrument. The diameter, flow range, lining material, electrode material and output current of the electromagnetic flowmeter should be determined according to the physical and chemical properties of the measured flow medium, and can adapt to the field environment and meet the technical indicators and performance requirements.

What are the advantages of electromagnetic flowmeter measurement for sewage measurement? The plug-in electromagnetic flowmeter is composed of two parts: flow sensor and transmitter.

Notes for electromagnetic flowmeter selection:

The measuring channel of the electromagnetic flowmeter is a smooth straight pipe of an unimpeded flow detector, which is not easy to block and is suitable for measuring liquid-solid two-phase fluids containing solid particles or fibers, such as paper pulp, coal water pulp, mineral pulp, mud and sewage.

Electromagnetic flow meters, also known as magmeters, are advanced devices used for measuring the flow rate of conductive fluids such as water and slurries. These meters operate based on the principles of electromagnetic induction. A magnetic field is generated by the meter’s coils, and as the conductive fluid flows through the meter’s pipe, it generates a voltage proportional to the flow rate. The strength of this induced voltage is directly correlated with the speed of the fluid, allowing for accurate and reliable flow measurements.

Four physical cleaning methods of electromagnetic flowmeter electrode

The grounding of the electromagnetic flowmeter is equipped with a grounding ring, and then the grounding ring is connected to the pipeline. If it’s lined, you need a third electrode to ground it.

Usually there is more or less a mixture in the fluid in the measurement of some occasions. In general, in the presence of a small bubbling flow of oil and gas bubbles, it is still able to work normally, but the measurement is a fusion of the volume of oil bubbles, if the proportion of oil and gas rises to have caused a projectile flow, then the electrode may be covered by gas, resulting in the circuit is disconnected, the output shake is more likely to be directly damaged.

The electromagnetic flowmeter uses the principle of Faraday’s electromagnetic induction law to calculate the flow rate by measuring the induced potential generated by the conductive liquid flowing in the magnetic field, and has the advantages of high precision, no mechanical wear, and two-way measurement.

Size: DN15mm-DN200mm
Nominal Pressure: 1.6Mpa
Accuracy: ±0.5%(Standard)
Liner: FEP, PFA
Output Signal: 4-20mA pulse frequency relay

Intelligent electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including acid, alkali, salt and other highly corrosive liquids.

Suitability of electromagnetic flowmeters in chlor-alkali measurement chlor-alkali occupation measurement of brine and caustic soda, both of which have the same characteristics:

Electromagnetic flowmeter is a widely used flow meter, in the process of use will inevitably appear some failures, then how to check the cause of the failure and eliminate it, the next Aister to teach you several simple troubleshooting methods.

The versatility of electromagnetic flowmeters is a testament to their robust performance across a wide range of conductive liquids. Whether dealing with water, acids, bases, or slurries, these flowmeters maintain their accuracy and reliability. This adaptability is particularly valuable in industries with varying fluid compositions, allowing for a single flowmeter type to be employed in diverse applications without sacrificing performance.

Protection Class: IP65(Standard); IP68(Optional for remote type)
Process Connection: Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal: 4-20mA/Pulse
Communication: RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply: AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption: <20W Alarm: Upper Limit Alarm / Lower Limit Alarm Self-diagnosis: Empty Pipe Alarm, Exciting Alarm Explosion Proof: ATEX

The correct selection of electromagnetic flowmeter is the prerequisite to ensure the good use of electromagnetic flowmeter. What kind of electromagnetic flowmeter should be selected should be determined according to the physical and chemical properties of the measured body medium, so that the diameter of the electromagnetic flowmeter, flow range, lining material, electrode material and output current, etc., can adapt to the nature and flow requirements of the measured body.

Typical fault diagnosis and treatment of electromagnetic flowmeter

Electromagnetic flowmeter is composed of two parts: sensor and converter. It is based on Faraday’s law of electromagnetic induction, used to measure the volume flow of conductive liquid with an electrical conductivity greater than 5μS/cm, is a kind of induction instrument to measure the volume flow of conductive medium.

Electromagnetic flowmeter is a kind of high precision, high reliability and long service life flow surface, which is composed of two parts: the sensor that directly contacts the pipeline medium and the upper end signal converter.

Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

The performance excellence of electromagnetic flowmeters is further underscored by their low maintenance requirements. The absence of mechanical components in direct contact with the fluid minimizes wear and tear, reducing the need for frequent maintenance interventions. This not only enhances the longevity of the flowmeter but also translates into cost savings for industries where operational efficiency is paramount.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa… Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type