SS304 SS316L Flow Meter for Waste Water of Magnetic Electromagnetic Flowmeter

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

The grounding of the electromagnetic flowmeter is equipped with a grounding ring, and then the grounding ring is connected to the pipeline. If it’s lined, you need a third electrode to ground it.

Selection of lining materials for electromagnetic flowmeter

What fault will occur during the debugging period of the plug-in electromagnetic flowmeter, the split electromagnetic flowmeter and the initial debugging fault, but once the fault is improved, it will generally not occur again under the same conditions.

Electromagnetic flowmeters, also known as magmeters, are widely used in various industries for measuring the flow rate of conductive fluids. They operate based on Faraday’s law of electromagnetic induction, where a voltage is induced in a conductor (the fluid) as it moves through a magnetic field. These flowmeters are favored for their accuracy, reliability, and suitability for a wide range of applications. Here are different categories of electromagnetic flowmeters and their fields of application:

Suitability of electromagnetic flowmeters in chlor-alkali measurement chlor-alkali occupation measurement of brine and caustic soda, both of which have the same characteristics:

Now, the input impedance of the electromagnetic flowmeter converter has improved a lot, and the error is basically not caused by changes in the conductivity of the medium when the conductive liquid is conductive, but for a certain converter input impedance, the conductivity of the measured medium has a lower limit min, which cannot be lower than this lower limit.

The correct selection of electromagnetic flowmeter is the prerequisite to ensure the good use of electromagnetic flowmeter. What kind of electromagnetic flowmeter should be selected should be determined according to the physical and chemical properties of the measured body medium, so that the diameter of the electromagnetic flowmeter, flow range, lining material, electrode material and output current, etc., can adapt to the nature and flow requirements of the measured body.

Environmental monitoring is another domain where electromagnetic flowmeters prove valuable. In applications related to ecological studies and environmental research, these flowmeters aid in measuring water flow in rivers, streams, and other natural water bodies. The data obtained contributes to a better understanding of ecosystems, water resource management, and environmental conservation efforts.

Measuring Range： Max 15m/s
Conductivity： >5us/cm
Protection Class： IP65(Standard); IP68(Optional for remote type)
Process Connection： Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal： 4-20mA/Pulse
Communication： RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply： AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption： <20W Alarm： Upper Limit Alarm / Lower Limit Alarm Self-diagnosis： Empty Pipe Alarm, Exciting Alarm Explosion Proof： ATEX

The ability of electromagnetic flowmeters to provide real-time data on fluid flow rates is a key performance aspect. Industries benefit from the immediate and accurate insights into their processes, allowing for proactive monitoring and control. This feature is especially crucial in applications such as water distribution networks, where real-time data facilitates efficient resource management and timely responses to changes in flow conditions.

Measuring Range: Max 15m/s
Conductivity: >5us/cm
Protection Class: IP65(Standard); IP68(Optional for remote type)
Process Connection: Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal: 4-20mA/Pulse
Communication: RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply: AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption: <20W Alarm: Upper Limit Alarm / Lower Limit Alarm Self-diagnosis: Empty Pipe Alarm, Exciting Alarm Explosion Proof: ATEX

As a measuring device with simple structure, sensitive response and not affected by physical properties such as temperature and viscosity of the measured medium, electromagnetic flowmeter has been widely used in the water supply industry, and has obtained good results.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Electromagnetic flow meters offer several advantages, making them a popular choice in various industrial applications. Here are some of the key advantages of electromagnetic flow meters:

Notes for electromagnetic flowmeter selection:

Installing electromagnetic flowmeters correctly is essential for ensuring accurate and reliable flow measurement. Here are some precautions to consider when installing electromagnetic flowmeters:

Electromagnetic flowmeter in the industry has achieved good results, then as the core accessories of electromagnetic flowmeter – electrode, electrode is contact with the measured medium more accessories, then the cleaning details of the electrode is a crucial point, of course, also pay attention to a certain method.

Electromagnetic flow meters, like any complex instrumentation, require effective fault diagnosis methods to ensure their optimal performance and reliability. One common approach to diagnosing issues with electromagnetic flow meters involves the analysis of the sensor signals. Any deviation from the expected output can be indicative of potential problems within the system. Advanced diagnostic algorithms can be employed to detect abnormalities in the induced voltage or electromagnetic field, allowing for the identification of faults such as sensor drift, signal noise, or electrode fouling.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

One key advantage of electromagnetic flow meters is their versatility in handling various fluid types and conditions. Since they rely on the conductivity of the fluid rather than its physical properties, these meters are suitable for a wide range of applications, from clean water to corrosive chemicals. Additionally, they exhibit minimal pressure loss, making them an energy-efficient choice for flow measurement systems.

In addition to signal analysis, real-time monitoring is a crucial aspect of fault diagnosis for electromagnetic flow meters. Continuous assessment of key parameters, such as fluid conductivity and temperature, can help detect anomalies that may impact meter accuracy. For instance, sudden changes in conductivity might signal issues like fluid contamination or changes in fluid composition, prompting the need for further investigation.

Electromagnetic water meters offer several advantages in water measurement applications, particularly in industrial and municipal settings. Here are some key advantages of electromagnetic water meters:

Electromagnetic flowmeter is a kind of induction meter to measure the volume flow of conductive medium, which can be used to measure the volume flow of strong corrosive liquid such as strong acid and alkali and uniform liquid-solid two-phase suspended liquid such as mud, pulp, pulp, etc.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Electromagnetic flowmeters, commonly known as magmeters, are a sophisticated and versatile type of flow measurement device widely used in industrial applications. Unlike traditional mechanical flow meters, electromagnetic flowmeters operate on the principle of electromagnetic induction to provide highly accurate and reliable measurements of liquid flow. The technology behind these devices makes them suitable for a diverse range of industries where precise flow measurement is crucial for various processes.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type

Electromagnetic flowmeter at work requires that the measured medium must be ground potential, generally through the pipeline or flange ground, if the process pipe connected to the sensor relative to the measured medium is insulated (plastic pipe or pipe with an insulating lining), you must choose a grounding ring or sensor with a grounding electrode, so that the measured medium in the ground potential, easy to be ignored in the actual design and installation.

electromagnetic flowmeters have emerged as indispensable tools for industries that demand accurate and reliable flow measurements. Their advanced technology, coupled with the ability to operate in diverse environments and handle various conductive liquids, positions them as a preferred choice in applications ranging from water management to chemical processing. As technology continues to evolve, electromagnetic flowmeters are likely to witness further advancements, contributing to increased efficiency and precision in liquid flow measurement across different sectors.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa… Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s
Conductivity: >5us/cm
Protection Class: IP65(Standard); IP68(Optional for remote type)
Process Connection: Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal: 4-20mA/Pulse
Communication: RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply: AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption: <20W Alarm: Upper Limit Alarm / Lower Limit Alarm Self-diagnosis: Empty Pipe Alarm, Exciting Alarm Explosion Proof: ATEX

The measuring principle of intelligent electromagnetic flowmeter is Faraday’s law of electromagnetic induction, which measures the flow of conductive fluid according to the electromotive force induced by the conductive fluid through the external magnetic field. The main components of the sensor are: measuring tube, electrode, excitation coil, iron core and yoke shell.

The electromagnetic flow meter consists of a non-conductive pipe lined with a conductive material, typically made of metal. The meter contains coils or electrodes positioned opposite each other on the pipe’s inner walls. A magnetic field is then generated by passing a current through these coils, creating a measurable voltage across the fluid. The induced voltage, or EMF, is directly proportional to the fluid’s velocity, allowing the flow meter to accurately determine the flow rate. Importantly, this principle remains effective regardless of the fluid’s conductivity, making electromagnetic flow meters suitable for a wide range of applications, including water, wastewater, and various industrial processes.

Electromagnetic flowmeter plays a multi-faceted role in farmland irrigation, mainly reflected in the following aspects: