Sewage electromagnetic flow meter

Electromagnetic flowmeters, also known as magmeters or magnetic flowmeters, typically generate electrical output signals proportional to the flow rate of a conductive fluid passing through a pipe. The most common output signals from electromagnetic flowmeters include:

Electromagnetic flowmeters are classified according to the assembly method of converters and sensors, with split type and one type. Split type electromagnetic flowmeter is relative to the integrated, its components are: measuring tube, electrode, excitation coil, iron core and yoke housing. Used to measure the volume flow of conductive liquid and slurry in closed pipes.

The electromagnetic flowmeter is constructed in such a way that it mainly consists of a number of key components that work together to measure the flow of a conductive liquid. The following is the main structure of the electromagnetic flowmeter and its functions:

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Calibration checks are another essential component of fault diagnosis for electromagnetic flow meters. Regular calibration against known standards ensures that the meter’s measurements remain accurate over time. Any deviation from the expected calibration values may indicate sensor degradation, electronic component failure, or other issues that require attention.

Non-full tube electromagnetic flowmeter is an advanced flow measuring instrument, especially suitable for measuring the flow of non-full tube or partially filled fluid, such as municipal rainwater, wastewater, sewage and so on. The following is a detailed introduction to the non-full tube electromagnetic flowmeter:

The material of construction is also a vital aspect in electromagnetic flowmeter selection. Different applications may require flowmeters made from specific materials to withstand corrosive environments or harsh chemicals. Ensuring that the materials of construction are compatible with the fluid and environmental conditions helps enhance the longevity and reliability of the flowmeter.

Another critical factor to consider is the flow rate range of the application. Electromagnetic flowmeters exhibit excellent accuracy and stability across a broad range of flow rates, making them suitable for both low-flow and high-flow applications. It is essential to match the flowmeter’s specifications, such as its minimum and maximum flow rates, with the expected flow conditions in the system.

Measuring Range： Max 15m/s
Conductivity： >5us/cm
Protection Class： IP65(Standard); IP68(Optional for remote type)
Process Connection： Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal： 4-20mA/Pulse
Communication： RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply： AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption： <20W Alarm： Upper Limit Alarm / Lower Limit Alarm Self-diagnosis： Empty Pipe Alarm, Exciting Alarm Explosion Proof： ATEX

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

The measuring channel of the electromagnetic flowmeter is a smooth straight pipe of an unimpeded flow detector, which is not easy to block and is suitable for measuring liquid-solid two-phase fluids containing solid particles or fibers, such as paper pulp, coal water pulp, mineral pulp, mud and sewage.

Electromagnetic flowmeter selection is generally more concerned with the measurement medium, temperature, pressure, connection form, protection level and whether explosion-proof.

The correct selection of electromagnetic flowmeter is the prerequisite to ensure the normal use of the instrument. The diameter, flow range, lining material, electrode material and output current of the electromagnetic flowmeter should be determined according to the physical and chemical properties of the measured flow medium, and can adapt to the field environment and meet the technical indicators and performance requirements.

In addition to signal analysis, real-time monitoring is a crucial aspect of fault diagnosis for electromagnetic flow meters. Continuous assessment of key parameters, such as fluid conductivity and temperature, can help detect anomalies that may impact meter accuracy. For instance, sudden changes in conductivity might signal issues like fluid contamination or changes in fluid composition, prompting the need for further investigation.

Due to various reasons, some large diameter flowmeters used online can not be tested off-line. It has become an urgent problem to study an online calibration method which is both scientific and effective and ADAPTS to the needs of the field. At present, there are three common methods for online calibration of electromagnetic flowmeters:

Intelligent electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including acid, alkali, salt and other highly corrosive liquids.

1. The role of the electromagnetic flowmeter grounding ring: the grounding ring is directly in contact with the medium through the grounding electrode, and then grounded with the flange of the electromagnetic flowmeter through the grounding ring to achieve equal potential with the ground to eliminate interference.

What are the advantages of electromagnetic flowmeter measurement for sewage measurement? The plug-in electromagnetic flowmeter is composed of two parts: flow sensor and transmitter.

With the speeding up of urbanization process in our country, environmental pollution is increasingly serious. Because in sewage treatment, it is necessary to analyze and control the discharged sewage, additives, sludge, etc., so the flow measurement is very important. Among the many flowmeter products used for sewage measurement, electromagnetic flowmeter measurement accuracy is higher.

Size DN3-DN3000mm
Nominal Pressure 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA

Several factors can contribute to the inaccurate measurement of flow by electromagnetic flowmeters. These factors can vary depending on the specific application, installation conditions, and characteristics of the fluid being measured. Here are some common reasons for inaccurate flow measurement with electromagnetic flowmeters:

Four physical cleaning methods of electromagnetic flowmeter electrode

Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

Electromagnetic flowmeter is a kind of instrument to measure the flow of conductive fluid by using Faraday’s law of electromagnetic induction according to the electromotive force generated by the flow cutting magnetic field line. The common faults of electromagnetic flowmeter are: no display, inaccurate flow measurement, air traffic control alarm, system alarm, upper and lower limit alarm, etc.

Fixed the electromagnetic flowmeter for periodic visual inspection, check the environment around the instrument, clean dirt, ensure that no water and other substances, check whether the wiring is good, check whether the electromagnetic flowmeter near the new installation of strong electromagnetic field equipment or a new wire across the instrument.

Electromagnetic flowmeters, also known as magmeters, are devices that measure the flow of electrically conductive fluids using the principles of electromagnetic induction. There are several types of electromagnetic flowmeters, each with its own characteristics and applications. Here are some common types:

Electromagnetic flow meters offer several advantages, making them a popular choice in various industrial applications. Here are some of the key advantages of electromagnetic flow meters:

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

The role of electromagnetic flow meter grounding in actual installation. Compared with other flowmeter products, electromagnetic flowmeter has high precision, reliable performance, stable work and excellent anti-interference ability. However, as a precision instrument, in order to meet these high requirements, it is necessary to have strict installation requirements, this article will introduce the electromagnetic flowmeter grounding wire that is often not paid attention to when installing.

Proper installation of electromagnetic flowmeters is crucial to ensure accurate and reliable measurement of fluid flow in various industrial applications. The first step in the installation process involves selecting an appropriate location for the flowmeter. It is essential to place the flowmeter in a section of the piping system where the flow profile is stable, avoiding areas with turbulence, elbows, or other disturbances that may affect the accuracy of measurements. Additionally, the installation site should provide easy access for maintenance and calibration activities.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse