Matters needing attention during the installation of thermal gas mass flowmeter

In practical applications, thermal mass flowmeters require careful attention to various factors to ensure accurate and reliable measurement of fluid flow rates. Here are some key considerations for the practical application of thermal mass flowmeters:

When selecting a thermal mass flowmeter, several important factors should be taken into consideration to ensure it meets the requirements of the application and provides accurate and reliable measurements. Here are key points to pay attention to:

The thermal gas mass flowmeter is an instrument for measuring fluid flow by using the principle of heat conduction. The instrument uses constant temperature difference method to accurately measure the gas mass flow.

Thermal gas mass flowmeter has certain operating procedures and precautions in use, and must pay attention to these points when in use:

Like the flue gas, this medium has a higher temperature, contains more impurities such as solid dust, the general application of large caliber, flow rate range is relatively wide, so the measurement is more difficult, so in the selection and use of flue gas flow timing should pay attention to the characteristics of the power plant flue wind speed, pay attention to the principle of choosing sensors, It is also necessary to pay attention to the wear resistance, corrosion resistance, dirt resistance and high temperature resistance of the sensor, and select the appropriate measurement position to ensure the measurement accuracy.

The thermal gas mass flowmeter is an instrument that uses the principle of heat conduction to measure fluid flow. The instrument uses the constant temperature difference method to measure the gas flow accurately. It has the advantages of small size, high digitization, easy installation and accurate measurement.

The thermal mass flowmeter is an device for measuring gas flow by using the principle of thermal diffusion. The sensor consists of two reference thermal resistors (RTDS). One is the speed sensor RH, and the other is the temperature sensor RMG, which measures the temperature change of the gas. When the two RTDS are placed in the measured gas, one sensor RH is heated and the other sensor RMG is used to sense the measured gas temperature. As the gas flow rate increases, the airflow carries away more heat, and the temperature of the sensor RH drops.

Measuring medium: Various gases (except acetylene gas)
Pipe diameter range: DN10-2000mm
Accuracy Degree: ±1～2.5%
Pipe material: Carbon steel, stainless steel, plastic, etc

The thermal gas flowmeter has many remarkable characteristics, which make it widely used in the field of gas flow measurement. The following are the main features of thermal gas flowmeters:

Thermal gas mass flowmeter as a gas flowmeter, the application is very wide, today we specifically understand the use of thermal gas mass flowmeter:

Thermal mass flowmeters are widely used in various industries due to their ability to measure the flow rate of gases accurately. Here are some applications of thermal mass flowmeters across different industries:

The thermal gas flowmeter adopts the principle of thermal diffusion, and the thermal diffusion technology is a technology with excellent performance and high reliability under harsh conditions. Typical sensing elements of thermal gas mass flowmeters include two thermal resistors (PT100), one is a speed sensor and one is a temperature sensor that automatically compensates for changes in gas temperature.

1. Principle of thermal gas mass flowmeter

Thermal gas mass flowmeter The thermal distributed flowmeter uses the flow fluid to transfer heat to change the heat conduction distribution effect of measuring the temperature distribution of the tube wall. 2) King’s Law using the heat dissipation (cooling) effect. And because the structure of the detection element extends into the measuring tube, also known as immersion or intrusion type. Some instruments that are inserted from outside the tube into the process tube when in use are called plug-in.

Although the thermal gas mass flowmeter has many advantages in this respect, it can not be used for large pipe runoff measurement, pressure loss is relatively large, and the price is more expensive, which limits its measurement application in natural gas long distance pipeline.

Thermal gas mass flowmeter has a wide range of applications in many fields, its high precision, rapid response and stability characteristics make it in a variety of gas flow measurement occasions can play an excellent performance, for the development of various industries to provide more reliable technical support.

Common faults encountered with thermal mass flowmeters can disrupt their accurate measurement capabilities. Here are some typical issues along with potential solutions:

The data show that in the flow measurement failure probability, the improper selection of flowmeter accounts for about 70%, and the quality of flowmeter products or other reasons account for 30%, which shows how important the selection of flow measurement is.

The thermal gas mass flowmeter is designed based on the principle of thermal diffusion. The meter uses constant temperature difference method to measure the gas accurately. The thermal gas mass flowmeter has the advantages of small volume, high digitization, easy installation and accurate measurement.

How to improve the accuracy of thermal gas mass flow meter?

At present, oxygen generator in the production process will be affected by external influences, more and more enterprises for fine management, energy consumption, cost accounting and other requirements for the loss of this part of the oxygen measurement.

With the development of new energy technology, natural gas is more and more widely used in many new energy industries, and the thermal gas mass flowmeter has become a suitable instrument for measuring high pressure gas measurement. Below we analyze from the perspective of product performance and installation cost, why the thermal gas mass flowmeter can become a suitable low degree meter in high pressure natural gas measurement.

Thermal mass flowmeters are known for their ability to provide accurate and reliable measurements of fluid flow rates, regardless of changes in pressure and temperature. This resilience to pressure and temperature variations is due to the operating principle of thermal mass flowmeters and their design features. Here’s why thermal mass flowmeters are not significantly affected by changes in pressure and temperature:

Thermal gas mass flowmeter is the use of fluid flowing through the pipe heated by an external heat source when the temperature field changes, is a high-sensitivity, high-precision gas measurement instrument, in the gas flow measurement conditions, good stability, used for gas process control and gas flow measurement one of the most used instruments.

When selecting a thermal mass flowmeter, several important factors should be taken into consideration to ensure it meets the requirements of the application and provides accurate and reliable measurements. Here are key points to pay attention to:

The medium of one of the two tubes of the thermal gas mass flowmeter does not flow, and the medium of the other tube flows. By comparing the Coriolis force of two pipes to obtain the flow rate, it is convenient to eliminate the natural vibration of the pipeline, the vibration of the fluid itself and other factors that affect or interfere with the measurement.

Thermal gas mass flow meter is used to measure and control the gas mass flow meter, different from other gas flow meters, do not need to carry out pressure and temperature correction, directly measure the gas mass flow.

In order to solve the problem of leakage caused by poor measurement accuracy or inability to measure below the lower limit of the instrument, a new type of thermal gas mass flowmeter is developed based on the theory of forced convection heat transfer and the principle of hot wire anemometer. The sensitivity of the instrument is greatly improved and the dead zone of the instrument is reduced by using microfilament structure in the sensitive element and the velocity measuring heating element.

The thermal gas mass flowmeter is an instrument that uses the principle of heat conduction to measure fluid flow. The instrument uses the constant temperature difference method to measure the gas flow accurately. It has the advantages of small size, high digitization, easy installation and accurate measurement. Today we are mainly to talk about the thermal gas mass flowmeter in the installation process need to pay attention to what are?

Choosing the correct installation direction for a thermal gas mass flowmeter is essential for optimal performance and accurate measurement. The installation direction should be determined based on factors such as the flow profile, flow conditions, and manufacturer recommendations. Here are some guidelines to help you choose the appropriate installation direction for a thermal gas mass flowmeter:

The thermal mass flowmeter is a flow meter based on the principle of thermal diffusion. The device uses the constant temperature difference method to measure the gas accurately. It has the advantages of small size, high digitization, easy installation, accurate measurement and so on.

Measuring medium: Various gases (except acetylene gas)
Pipe diameter range: DN10-2000mm
Accuracy Degree: ±1～2.5%
Pipe material: Carbon steel, stainless steel, plastic, etc

Thermal gas mass flowmeter is the use of fluid flowing through the pipe heated by an external heat source when the temperature field changes, is a high-sensitivity, high-precision gas measurement instrument, in the gas flow measurement conditions, good stability, used for gas process control and gas flow measurement one of the most used instruments.