Liquid Control Electromagnetic Water Flowmeter 4-20mA Pulse Output Magnetic Flow Meter

The installation distance between an electromagnetic flowmeter and a control valve, especially a rear valve, is a critical factor that can impact the accuracy and reliability of flow measurements. Here are some general guidelines to help determine the appropriate installation distance:

Electromagnetic flowmeters find applications in numerous industries due to their adaptability and precision. They are extensively used in water and wastewater management for monitoring water distribution, sewage treatment, and environmental compliance. In chemical and petrochemical industries, these flowmeters excel in measuring the flow of corrosive and abrasive liquids. The food and beverage sector benefits from their accuracy in ensuring consistent liquid measurements during production processes. In pharmaceutical manufacturing, electromagnetic flowmeters contribute to the precise control of liquid ingredients, while in mining and minerals processing, they help optimize the efficiency of slurry flow.

Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s
Conductivity: >5us/cm
Protection Class: IP65(Standard); IP68(Optional for remote type)
Process Connection: Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal: 4-20mA/Pulse
Communication: RS485(Standard), HART(Optional),GPRS/GSM (Optional)

As a measuring device with simple structure, sensitive response and not affected by physical properties such as temperature and viscosity of the measured medium, electromagnetic flowmeter has been widely used in the water supply industry, and has obtained good results.

When using electromagnetic flowmeters in the field, it’s important to perform regular checks and maintenance to ensure accurate and reliable flow measurements. Here are some key parameters to check and consider in the field for electromagnetic flowmeter use:

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Electromagnetic flowmeters, commonly known as magmeters, are a sophisticated and versatile type of flow measurement device widely used in industrial applications. Unlike traditional mechanical flow meters, electromagnetic flowmeters operate on the principle of electromagnetic induction to provide highly accurate and reliable measurements of liquid flow. The technology behind these devices makes them suitable for a diverse range of industries where precise flow measurement is crucial for various processes.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type

Due to various reasons, some large diameter flowmeters used online can not be tested off-line. It has become an urgent problem to study an online calibration method which is both scientific and effective and ADAPTS to the needs of the field. At present, there are three common methods for online calibration of electromagnetic flowmeters:

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Electromagnetic flowmeters, also known as magmeters, are devices that measure the flow of electrically conductive fluids using the principles of electromagnetic induction. There are several types of electromagnetic flowmeters, each with its own characteristics and applications. Here are some common types:

electromagnetic flowmeters are employed in HVAC (heating, ventilation, and air conditioning) systems to measure the flow of water or other fluids used for temperature control. The precision and reliability of these flowmeters ensure optimal performance of HVAC systems, leading to energy savings and improved comfort in various buildings and facilities.

Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range： Max 15m/s
Conductivity： >5us/cm
Protection Class： IP65(Standard); IP68(Optional for remote type)
Process Connection： Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal： 4-20mA/Pulse
Communication： RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply： AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)

Electromagnetic flow meters, like any complex instrumentation, require effective fault diagnosis methods to ensure their optimal performance and reliability. One common approach to diagnosing issues with electromagnetic flow meters involves the analysis of the sensor signals. Any deviation from the expected output can be indicative of potential problems within the system. Advanced diagnostic algorithms can be employed to detect abnormalities in the induced voltage or electromagnetic field, allowing for the identification of faults such as sensor drift, signal noise, or electrode fouling.

The converter direction of an electromagnetic flowmeter refers to the orientation or alignment of the flowmeter’s electronic converter unit concerning the flow direction within the pipe. Electromagnetic flowmeters typically have a preferred or specified direction for the converter to achieve optimal performance. The converter contains the electronics and signal processing components essential for accurate flow measurement.

The measuring accuracy and stability of the electromagnetic flowmeter is directly related to whether the electromagnetic flowmeter housing is grounded.

Electromagnetic flowmeter is a kind of induction meter to measure the volume flow of conductive medium, which can be used to measure the volume flow of strong corrosive liquid such as strong acid and alkali and uniform liquid-solid two-phase suspended liquid such as mud, pulp, pulp, etc.

Suitability of electromagnetic flowmeters in chlor-alkali measurement chlor-alkali occupation measurement of brine and caustic soda, both of which have the same characteristics:

The shell protection level of the ordinary electromagnetic flowmeter sensor is IP65 (the dustproof and anti-splash level stipulated by GB4208), and the requirements for the installation site are:

The scale of the water supply system itself is huge, and the environment in which it is located is complex and changeable, requiring the electromagnetic flowmeter to have strong stability and reliability, so in the actual use process, the matters needing attention should be clear.

The transducer in the split electromagnetic flowmeter can form a body or separate type with the sensor, the integrated electromagnetic flowmeter is the integrated electromagnetic flowmeter, the split type becomes the split electromagnetic flowmeter, the flowmeter is a two-way measurement system, and the three integrators are installed: the forward total, the reverse total and the difference total

Several electromagnetic flowmeters are used in the gasification unit, and the faults encountered during the test run of the gasification unit are as follows:

Electromagnetic flowmeter is based on the principle of electromagnetic induction, through the electromotive force generated by the conductive fluid through the external magnetic field to measure the fluid flow meter. Electromagnetic flowmeter is widely used because of its high precision and good stability, so the choice of integrated or split electromagnetic flowmeter is particularly important.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Intelligent electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including acid, alkali, salt and other highly corrosive liquids.

The use of electromagnetic flowmeters is very wide, and this measuring instrument is used in many industries. Electromagnetic flowmeter is different from the general flowmeter, it follows the principle of electromagnetic induction, can measure the flow of liquid in the pipeline and its velocity.

The application of flowmeter in food processing is very extensive, mainly reflected in the following aspects:

Typical fault diagnosis and treatment of electromagnetic flowmeter

Electromagnetic flowmeter is widely used in the industrial field, in order to make the electromagnetic flowmeter work stable and reliable, accurate measurement, installation needs to be installed in accordance with the correct method.

Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

The electromagnetic flow meter consists of a non-conductive pipe lined with a conductive material, typically made of metal. The meter contains coils or electrodes positioned opposite each other on the pipe’s inner walls. A magnetic field is then generated by passing a current through these coils, creating a measurable voltage across the fluid. The induced voltage, or EMF, is directly proportional to the fluid’s velocity, allowing the flow meter to accurately determine the flow rate. Importantly, this principle remains effective regardless of the fluid’s conductivity, making electromagnetic flow meters suitable for a wide range of applications, including water, wastewater, and various industrial processes.

The requirements of the straight tube section of the electromagnetic flowmeter are very important to ensure the accuracy and stability of the measurement results. The following is a detailed analysis of the requirements of the straight pipe section before and after the electromagnetic flowmeter:

Selecting the appropriate installation point for an electromagnetic flowmeter is crucial for accurate and reliable measurements. Here are some considerations and guidelines to help you choose the right measuring installation point: