IP68 Water-Proof 4-20mA Pulse Alarm Output Sewage Water Electromagnetic Flow Meter

In the flow measurement of domestic sewage, it is very important to choose the right flowmeter to ensure the accuracy and reliability of the measurement results. Here are some suggestions to help you choose the right flowmeter for domestic sewage:

1. The role of the electromagnetic flowmeter grounding ring: the grounding ring is directly in contact with the medium through the grounding electrode, and then grounded with the flange of the electromagnetic flowmeter through the grounding ring to achieve equal potential with the ground to eliminate interference.

The grounding ring is a crucial component in the installation of an electromagnetic flowmeter as it helps establish proper grounding and ensures accurate and reliable measurements. Here’s a general guide on how to install an electromagnetic flowmeter grounding ring:

The converter direction of an electromagnetic flowmeter refers to the orientation or alignment of the flowmeter’s electronic converter unit concerning the flow direction within the pipe. Electromagnetic flowmeters typically have a preferred or specified direction for the converter to achieve optimal performance. The converter contains the electronics and signal processing components essential for accurate flow measurement.

Non-full tube electromagnetic flowmeter is an advanced flow measuring instrument, especially suitable for measuring the flow of non-full tube or partially filled fluid, such as municipal rainwater, wastewater, sewage and so on. The following is a detailed introduction to the non-full tube electromagnetic flowmeter:

Fixed the electromagnetic flowmeter for periodic visual inspection, check the environment around the instrument, clean dirt, ensure that no water and other substances, check whether the wiring is good, check whether the electromagnetic flowmeter near the new installation of strong electromagnetic field equipment or a new wire across the instrument.

The measuring channel of the electromagnetic flowmeter is a smooth straight pipe of an unimpeded flow detector, which is not easy to block and is suitable for measuring liquid-solid two-phase fluids containing solid particles or fibers, such as paper pulp, coal water pulp, mineral pulp, mud and sewage.

Electromagnetic flowmeters, commonly known as magmeters, are a sophisticated and versatile type of flow measurement device widely used in industrial applications. Unlike traditional mechanical flow meters, electromagnetic flowmeters operate on the principle of electromagnetic induction to provide highly accurate and reliable measurements of liquid flow. The technology behind these devices makes them suitable for a diverse range of industries where precise flow measurement is crucial for various processes.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

In the energy sector, particularly in power generation plants, electromagnetic flowmeters play a critical role in measuring cooling water flow. The accuracy and stability of these flowmeters help power plants maintain optimal operating conditions and monitor the efficiency of their cooling systems. Additionally, electromagnetic flowmeters are used in the oil and gas industry for measuring the flow of hydrocarbons, providing crucial data for production and transportation processes.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range： Max 15m/s
Conductivity： >5us/cm

Electromagnetic flowmeters find versatile applications across various industries due to their precision and reliability in measuring fluid flow. One primary area of application is in water and wastewater management, where these flowmeters excel in accurately measuring the flow of water and other conductive fluids. Municipalities and water treatment plants utilize electromagnetic flowmeters to monitor water distribution networks, optimize usage, and ensure efficient wastewater processing.

Measuring Range： Max 15m/s
Conductivity： >5us/cm
Protection Class： IP65(Standard); IP68(Optional for remote type)
Process Connection： Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal： 4-20mA/Pulse
Communication： RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply： AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption： <20W Alarm： Upper Limit Alarm / Lower Limit Alarm Self-diagnosis： Empty Pipe Alarm, Exciting Alarm Explosion Proof： ATEX

Intelligent electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including acid, alkali, salt and other highly corrosive liquids.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

The electromagnetic flow meter consists of a non-conductive pipe lined with a conductive material, typically made of metal. The meter contains coils or electrodes positioned opposite each other on the pipe’s inner walls. A magnetic field is then generated by passing a current through these coils, creating a measurable voltage across the fluid. The induced voltage, or EMF, is directly proportional to the fluid’s velocity, allowing the flow meter to accurately determine the flow rate. Importantly, this principle remains effective regardless of the fluid’s conductivity, making electromagnetic flow meters suitable for a wide range of applications, including water, wastewater, and various industrial processes.

Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

What are the external interference problems of the electromagnetic flowmeter for domestic wastewater

Dealing with a weak signal issue in an intelligent electromagnetic flowmeter is crucial to ensure accurate and reliable flow measurements. Weak signals can be caused by various factors, and addressing them requires a systematic troubleshooting approach. Here are some steps to help you diagnose and resolve the weak signal phenomenon:

Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

The selection of circulating water flowmeter is a decision process involving many aspects, which needs to consider the characteristics of circulating water, measurement requirements, environmental conditions, economic costs and the performance characteristics of the flowmeter. Here is a comprehensive analysis and recommendations for the best options:

The scale of the water supply system itself is huge, and the environment in which it is located is complex and changeable, requiring the electromagnetic flowmeter to have strong stability and reliability, so in the actual use process, the matters needing attention should be clear.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Several factors can contribute to the inaccurate measurement of flow by electromagnetic flowmeters. These factors can vary depending on the specific application, installation conditions, and characteristics of the fluid being measured. Here are some common reasons for inaccurate flow measurement with electromagnetic flowmeters:

Electromagnetic flowmeters, also known as magmeters or magnetic flowmeters, typically generate electrical output signals proportional to the flow rate of a conductive fluid passing through a pipe. The most common output signals from electromagnetic flowmeters include:

One notable advantage of electromagnetic flow meters is their ability to measure bidirectional flow accurately. As the induced voltage is directly proportional to the fluid’s velocity, these meters are highly responsive to changes in flow rates, enabling real-time monitoring and control. Additionally, electromagnetic flow meters are not affected by factors such as temperature, pressure, or viscosity, ensuring consistent and reliable performance across diverse operating conditions. This working principle, coupled with their durability and low maintenance requirements, makes electromagnetic flow meters a preferred choice in industries requiring precise and stable flow measurements.

Electromagnetic flowmeters can achieve remote communication through various digital communication protocols. These protocols allow flowmeter data to be transmitted to remote monitoring systems, control rooms, or other devices for real-time monitoring, analysis, and control. Some common digital communication protocols used for remote communication with electromagnetic flowmeters include:

In addition to signal analysis, real-time monitoring is a crucial aspect of fault diagnosis for electromagnetic flow meters. Continuous assessment of key parameters, such as fluid conductivity and temperature, can help detect anomalies that may impact meter accuracy. For instance, sudden changes in conductivity might signal issues like fluid contamination or changes in fluid composition, prompting the need for further investigation.

The design of electromagnetic flow meters contributes to their robustness and long-term reliability. With no moving parts in contact with the fluid, they experience less wear and tear, resulting in extended operational life and reduced maintenance requirements. This makes them particularly suitable for applications where low-maintenance and high durability are crucial factors.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

The material of construction is also a vital aspect in electromagnetic flowmeter selection. Different applications may require flowmeters made from specific materials to withstand corrosive environments or harsh chemicals. Ensuring that the materials of construction are compatible with the fluid and environmental conditions helps enhance the longevity and reliability of the flowmeter.

Another critical factor to consider is the flow rate range of the application. Electromagnetic flowmeters exhibit excellent accuracy and stability across a broad range of flow rates, making them suitable for both low-flow and high-flow applications. It is essential to match the flowmeter’s specifications, such as its minimum and maximum flow rates, with the expected flow conditions in the system.

Measuring Range： Max 15m/s
Conductivity： >5us/cm
Protection Class： IP65(Standard); IP68(Optional for remote type)
Process Connection： Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal： 4-20mA/Pulse
Communication： RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply： AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption： <20W Alarm： Upper Limit Alarm / Lower Limit Alarm Self-diagnosis： Empty Pipe Alarm, Exciting Alarm Explosion Proof： ATEX