Food Grade SS304 Sanitary Electromagnetic Flow Meter Beverage Milk Magnetic Flowmeter

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Electromagnetic flow meters, also known as magmeters, are advanced devices used for measuring the flow rate of conductive fluids such as water and slurries. These meters operate based on the principles of electromagnetic induction. A magnetic field is generated by the meter’s coils, and as the conductive fluid flows through the meter’s pipe, it generates a voltage proportional to the flow rate. The strength of this induced voltage is directly correlated with the speed of the fluid, allowing for accurate and reliable flow measurements.

Electromagnetic flowmeters are used to measure the volume flow of industrial liquids and there are many media in industrial liquids, electromagnetic flowmeters are often used to measure the flow of conductive media.

Intelligent electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including acid, alkali, salt and other highly corrosive liquids.

Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Calibration checks are another essential component of fault diagnosis for electromagnetic flow meters. Regular calibration against known standards ensures that the meter’s measurements remain accurate over time. Any deviation from the expected calibration values may indicate sensor degradation, electronic component failure, or other issues that require attention.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

High voltage electromagnetic flowmeters are commonly used in applications where the measurement of electrically conductive fluids is required. These flowmeters operate based on Faraday’s law of electromagnetic induction and are suitable for a variety of industrial processes. Here are some key application characteristics of high voltage electromagnetic flowmeters:

In the energy sector, particularly in power generation plants, electromagnetic flowmeters play a critical role in measuring cooling water flow. The accuracy and stability of these flowmeters help power plants maintain optimal operating conditions and monitor the efficiency of their cooling systems. Additionally, electromagnetic flowmeters are used in the oil and gas industry for measuring the flow of hydrocarbons, providing crucial data for production and transportation processes.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range： Max 15m/s
Conductivity： >5us/cm

Electromagnetic flow meters offer several advantages, making them a popular choice in various industrial applications. Here are some of the key advantages of electromagnetic flow meters:

Electromagnetic flowmeter is widely used in the industrial field, in order to make the electromagnetic flowmeter work stable and reliable, accurate measurement, installation needs to be installed in accordance with the correct method.

In the flow measurement of domestic sewage, it is very important to choose the right flowmeter to ensure the accuracy and reliability of the measurement results. Here are some suggestions to help you choose the right flowmeter for domestic sewage:

Electromagnetic flowmeters exhibit remarkable performance even in challenging environmental conditions. Their construction materials are often chosen for their corrosion resistance, enabling these devices to withstand harsh chemicals and extreme temperatures. This robustness ensures continuous and reliable operation, making electromagnetic flowmeters suitable for demanding industrial applications where other flow measurement devices might struggle to perform consistently.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa… Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s
Conductivity: >5us/cm

For the daily inspection of the electromagnetic flow meter, in addition to the inspection of the sensor we talked about last time, it is also necessary to check the sensor of the electromagnetic flow meter, connecting cables, etc., below we will understand how to operate.

Four physical cleaning methods of electromagnetic flowmeter electrode

Fixed the electromagnetic flowmeter for periodic visual inspection, check the environment around the instrument, clean dirt, ensure that no water and other substances, check whether the wiring is good, check whether the electromagnetic flowmeter near the new installation of strong electromagnetic field equipment or a new wire across the instrument.

Usually there is more or less a mixture in the fluid in the measurement of some occasions. In general, in the presence of a small bubbling flow of oil and gas bubbles, it is still able to work normally, but the measurement is a fusion of the volume of oil bubbles, if the proportion of oil and gas rises to have caused a projectile flow, then the electrode may be covered by gas, resulting in the circuit is disconnected, the output shake is more likely to be directly damaged.

The use of electromagnetic flowmeters is very wide, and this measuring instrument is used in many industries. Electromagnetic flowmeter is different from the general flowmeter, it follows the principle of electromagnetic induction, can measure the flow of liquid in the pipeline and its velocity.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Electromagnetic flowmeter is a speed meter to measure the volume flow of conductive media. While carrying out on-site monitoring and display, it can output standard current signals for recording, adjustment and control, realizing automatic control of detection, and realizing long-distance transmission of signals. It can be widely used in water, chemical, coal, environmental protection, textile, metallurgy, paper and other industries in the flow measurement of conductive liquid. The structure of the instrument has one type and one type.

Performance Technical parameter
Size DN3-DN3000mm
Nominal Pressure 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy +/-0.5%(Standard)     +/-0.3% or +/-0.2%(Optional)
Liner PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode SUS316L, Hastelloy B, Hastelloy C       Titanium, Tantalum, Platinium-iridium
Structure Type Integral type, remote type, submersible type, ex-proof type
Medium Temperature -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature -20~+60deg C
Ambient Humidity 5-100%RH(relative humidity)
Measuring Range Max 15m/s
Conductivity >5us/cm
Protection Class IP65(Standard); IP68(Optional for remote type)
Process Connection Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal 4-20mA/Pulse
Communication RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption <20W Alarm Upper Limit Alarm / Lower Limit Alarm Self-diagnosis Empty Pipe Alarm, Exciting Alarm Explosion Proof ATEX

Electromagnetic flowmeters are classified according to the assembly method of converters and sensors, with split type and one type. Split type electromagnetic flowmeter is relative to the integrated, its components are: measuring tube, electrode, excitation coil, iron core and yoke housing. Used to measure the volume flow of conductive liquid and slurry in closed pipes.

Electromagnetic flowmeters find applications in numerous industries due to their adaptability and precision. They are extensively used in water and wastewater management for monitoring water distribution, sewage treatment, and environmental compliance. In chemical and petrochemical industries, these flowmeters excel in measuring the flow of corrosive and abrasive liquids. The food and beverage sector benefits from their accuracy in ensuring consistent liquid measurements during production processes. In pharmaceutical manufacturing, electromagnetic flowmeters contribute to the precise control of liquid ingredients, while in mining and minerals processing, they help optimize the efficiency of slurry flow.

Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s
Conductivity: >5us/cm
Protection Class: IP65(Standard); IP68(Optional for remote type)
Process Connection: Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal: 4-20mA/Pulse
Communication: RS485(Standard), HART(Optional),GPRS/GSM (Optional)

Drainage flowmeter, sewage outfall flowmeter installation position

When measuring waste acid using an electromagnetic flowmeter, it’s crucial to choose electrodes that are suitable for the corrosive nature of the acid and that can withstand the specific conditions of the application. Common electrode materials for electromagnetic flowmeters used in corrosive environments include:

Electromagnetic flowmeter in the industry has achieved good results, then as the core accessories of electromagnetic flowmeter – electrode, electrode is contact with the measured medium more accessories, then the cleaning details of the electrode is a crucial point, of course, also pay attention to a certain method.

The performance excellence of electromagnetic flowmeters is further underscored by their low maintenance requirements. The absence of mechanical components in direct contact with the fluid minimizes wear and tear, reducing the need for frequent maintenance interventions. This not only enhances the longevity of the flowmeter but also translates into cost savings for industries where operational efficiency is paramount.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa… Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type

How to correctly select the installation point of the electromagnetic flowmeter

What are the advantages of electromagnetic flowmeter measurement for sewage measurement? The plug-in electromagnetic flowmeter is composed of two parts: flow sensor and transmitter.

Electromagnetic flowmeter in the use process will produce some faults affect the normal work of the instrument, how to find the cause behind the fault is a very important work, we need to identify through a variety of different types of detection methods, in general, we for electromagnetic flowmeter routine testing, usually including electrode contact resistance, electrode polarization voltage, Signal cable interference, the determination of whether there is a grounding potential and the flow of stray current in the pipeline five aspects, these five aspects can be carried out separately, in fact, but also interrelated, any change in the factor may cause other changes, this reminds everyone in the detection of special attention: