Liquid Turbine Flow Meter

As far as the accuracy of turbine flowmeter measurement is concerned, it can be considered from the following 4 aspects:

(1) The horizontally installed sensor of the turbine flowmeter requires that the pipe should not have a visually perceptible tilt (within 5°). The vertical deviation of the vertically installed sensor pipe should be less than 5°, and the fluid direction should be down and up.

Turbine flowmeter has become one of the indispensable measuring instruments, turbine flowmeter selection, need to pay attention to the following points.

Turbine flowmeter interference fault phenomenon, fault causes and elimination methods

Turbine flowmeter is a kind of precision flow measuring instrument, which can be used to measure the flow and total amount of liquid with the corresponding flow integrating instrument. Widely used in petroleum, chemical industry, metallurgy, scientific research and other fields of measurement, control system. Turbine flow meter sensors equipped with sanitary connectors can be used in pharmaceutical, food and other industries.

In the case that the type of flow sensor has been selected, the selection of the flow sensor specification and its supporting components is very important. In a word, choose well to use well. Therefore, two basic principles should be grasped in the selection process of turbine flowmeter; To wit:

Turbine flowmeter has the characteristics of simple structure, light weight, high precision, good repeatability, sensitive response, easy installation and maintenance, etc., widely used in petroleum, chemical industry, metallurgy, water supply, paper and other industries.

Intelligent turbine flowmeter is a very popular flow meter, the reason why it is popular, in addition to its convenient use and high precision, there is also a very important point, that is, when it is used, it has a long service life, which is also very important, because all the units or individuals who use this thing also want to long-term use.

Liquid turbine flowmeter mainly uses advanced single-chip microcomputer technology, is a new type of flow meter and traditional turbine flow sensor and secondary meter measurement system, compared with its smaller volume, and intuitive reading display, turbine flowmeter in the measurement, will not be affected by external power supply, and has a good anti-lightning meter low cost advantage.

Liquid turbine flowmeter mainly uses advanced single-chip microcomputer technology, is a new type of flow meter and traditional turbine flow sensor and secondary meter measurement system, compared with its smaller volume, and intuitive reading display, turbine flowmeter in the measurement, will not be affected by external power supply, and has a good anti-lightning meter low cost advantage.

When selecting a turbine flow meter brand with excellent quality and good reputation, it can be considered from the following aspects:

the characteristics of liquid turbine flowmeters include high accuracy, wide rangeability, compact design, durability, and quick response times. These qualities collectively contribute to their effectiveness and reliability in measuring liquid flow rates across diverse industrial applications.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

liquid turbine flowmeters are known for their quick response times. The turbine mechanism enables rapid detection and adaptation to changes in liquid flow rates, providing real-time data for process monitoring and control. This characteristic is particularly valuable in industries where timely adjustments are crucial for maintaining operational efficiency.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

The compact and lightweight design of liquid turbine flowmeters is another defining characteristic. Their relatively simple construction makes them easy to install and maintain. The compact size is particularly advantageous in applications where space constraints are a consideration. The simplicity of their design also reduces the likelihood of clogs or obstructions, contributing to their reliability and minimizing downtime.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Durability and robustness are inherent characteristics of liquid turbine flowmeters, enabling them to withstand harsh industrial environments. Constructed from materials that resist corrosion and wear, these flowmeters are well-suited for applications involving corrosive liquids, high pressures, and extreme temperatures. This durability ensures a longer operational life and reduces the need for frequent maintenance or replacements.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Another notable characteristic of liquid turbine flowmeters is their wide rangeability. These flowmeters can effectively measure a broad spectrum of flow rates, from low to high, while maintaining consistent accuracy. This versatility is crucial in industries where liquid flow rates can vary significantly, allowing for the measurement of different flow conditions without sacrificing measurement precision.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Liquid turbine flowmeters exhibit several key characteristics that make them well-suited for a variety of industrial applications. One significant characteristic is their high accuracy in measuring liquid flow rates. The turbine mechanism within the flowmeter, combined with precise calibration, allows for reliable and precise measurements, making them essential in industries where accuracy is paramount for process control and optimization.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

the versatile applications of liquid turbine flowmeters span industries such as water management, chemical manufacturing, pharmaceuticals, oil and gas, and HVAC systems. Their ability to deliver accurate and real-time liquid flow measurements makes them indispensable for enhancing efficiency, safety, and precision in a wide range of industrial processes.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

liquid turbine flowmeters are utilized in HVAC (heating, ventilation, and air conditioning) systems to measure the flow of liquids such as water or refrigerants. In this context, they contribute to the efficiency of temperature control systems by providing accurate flow data, enabling precise adjustments and optimal energy utilization in commercial and residential buildings.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

In the oil and gas sector, liquid turbine flowmeters are employed for measuring the flow of hydrocarbons in pipelines. Their robust construction and ability to withstand harsh conditions make them well-suited for applications in oil refineries, where accurate flow measurements are crucial for optimizing production processes and ensuring compliance with industry standards.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Liquid turbine flowmeters also find application in the pharmaceutical industry, where precise measurements of liquid flow rates are vital for the production of pharmaceutical products. From monitoring the flow of ingredients during manufacturing to ensuring accurate dosing in pharmaceutical research and development, these flowmeters contribute to the quality and consistency of pharmaceutical processes.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Liquid turbine flowmeters also find application in the pharmaceutical industry, where precise measurements of liquid flow rates are vital for the production of pharmaceutical products. From monitoring the flow of ingredients during manufacturing to ensuring accurate dosing in pharmaceutical research and development, these flowmeters contribute to the quality and consistency of pharmaceutical processes.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

In the chemical and petrochemical industries, liquid turbine flowmeters play a crucial role in measuring the flow of various liquids, including corrosive chemicals and petroleum products. Their ability to handle a wide range of liquids, coupled with high accuracy, makes them essential for monitoring and controlling processes in chemical manufacturing, ensuring precision and safety in handling potentially hazardous substances.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Liquid turbine flowmeters find widespread applications across various industries due to their versatility, accuracy, and reliability in measuring liquid flow rates. One prominent application is in the field of water management, where these flowmeters are utilized to measure the flow of water in distribution systems, wastewater treatment plants, and irrigation networks. The accurate and real-time data provided by liquid turbine flowmeters contribute to efficient water resource management and conservation efforts.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Liquid turbine flowmeters offer several advantages that make them a popular choice for measuring the flow of liquids in various industrial applications. One significant advantage is their high accuracy in providing precise measurements of liquid flow rates. These flowmeters are capable of delivering reliable data, making them essential for industries where accurate monitoring and control of fluid processes are critical for operational success.

Connection mode: Thread, clamp, flange, clamp type
Accuracy: ±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material: 304, 316 stainless steel, etc
Use conditions: Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function: Pulse signal, 4-20mA signal
Communication output function: RS485 communication, HART protocol, etc

A liquid turbine flow meter is a type of flow meter designed to measure the flow rate of liquid substances, such as water, chemicals, or petroleum-based fluids. It operates on the principle of a turbine inserted into the flow stream. As the liquid flows through the meter, it causes the turbine to rotate. The rotational speed of the turbine is directly proportional to the velocity of the liquid, allowing for accurate measurement of the flow rate.

Liquid turbine flow meters are devices used to measure the flow of liquids through a pipeline. They operate on the principle of a turbine rotor turning in response to fluid flow. Here are some advantages of liquid turbine flow meters:

Liquid turbine flow meters are devices used to measure the flow of liquids through a pipeline. They operate on the principle of a turbine rotor turning in response to fluid flow. Here are some advantages of liquid turbine flow meters:

Accuracy: ±0.5%, ±0.2% Optional
Sensor Material: SS304, SS316L Optional
Signal Output: Pulse, 4-20mA, Alarm(optional)
Digital Communication: MODBUS RS485; HART
Power Supply: 24V DC/3.6V Lithium Battery

Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display