DN40 3-24V DC Magnetic Hall Effect Liquid Flow Sensor 4-45L/Min Turbine Water Flow Meter

Liquid turbine flow meters are devices used to measure the flow of liquids through a pipeline. They operate on the principle of a turbine rotor turning in response to fluid flow. Here are some advantages of liquid turbine flow meters:

Nominal diameter: DN4-DN200mm
Accuracy: ±1%R、±0.5%R、±0.2%R (to be customized)
Instrument type: Field display type, pulse output type, 4-20mA output type, split remote display type
Applicable medium: No impurities, low viscosity, no strong corrosive liquid

Another notable characteristic of liquid turbine flowmeters is their wide rangeability. These flowmeters can effectively measure a broad spectrum of flow rates, from low to high, while maintaining consistent accuracy. This versatility is crucial in industries where liquid flow rates can vary significantly, allowing for the measurement of different flow conditions without sacrificing measurement precision.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Nominal diameter: DN15-DN200mm
Accuracy level: ±1%R、±0.5%R、±0.2%R (to be customized)
Instrument type: Field display type, pulse output type, 4-20mA output type, split remote display type
Applicable medium: No impurities, low viscosity, no strong corrosive liquid

In the oil and gas sector, liquid turbine flowmeters are employed for measuring the flow of hydrocarbons in pipelines. Their robust construction and ability to withstand harsh conditions make them well-suited for applications in oil refineries, where accurate flow measurements are crucial for optimizing production processes and ensuring compliance with industry standards.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Size: DN4,6,10,15,20,32,40,50,65,80
Accuracy: ±0.5% (±0.2% Optional)
Sensor Material: SS304 (SS316L Optional)
Signal Output: Pulse, 4-20mA
Digital Communication: MODBUS RS485, HART

Nominal diameter: DN15-DN200mm
Accuracy level: ±1%R、±0.5%R、±0.2%R (to be customized)
Instrument type: Field display type, pulse output type, 4-20mA output type, split remote display type
Applicable medium: No impurities, low viscosity, no strong corrosive liquid

Turbine flow meters are used to measure clean, dry gases and liquids such as hydrocarbons, chemicals, gases and vapors, fuels and other types of liquids with lower viscosity, and for applications requiring highly accurate and precise measurements.

Nominal diameter: DN4-DN200mm
Accuracy: ±1%R、±0.5%R、±0.2%R (to be customized)
Instrument type: Field display type, pulse output type, 4-20mA output type, split remote display type
Applicable medium: No impurities, low viscosity, no strong corrosive liquid

liquid turbine flowmeters are known for their quick response times. The turbine mechanism enables rapid detection and adaptation to changes in liquid flow rates, providing real-time data for process monitoring and control. This characteristic is particularly valuable in industries where timely adjustments are crucial for maintaining operational efficiency.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Liquid turbine flowmeter is a kind of precision flow measuring instrument, which can be used to measure the flow and total amount of liquid with the corresponding flow integrating instrument. Liquid turbine flowmeters are widely used in measurement and control systems in petroleum, chemical industry, metallurgy, scientific research and other fields. Liquid turbine flowmeters with sanitary fittings can be used in the pharmaceutical industry.

Nominal diameter: DN4-DN200mm
Accuracy: ±1%R、±0.5%R、±0.2%R (to be customized)
Instrument type: Field display type, pulse output type, 4-20mA output type, split remote display type
Applicable medium: No impurities, low viscosity, no strong corrosive liquid

Liquid turbine flow meters are devices used to measure the flow of liquids through a pipeline. They operate on the principle of a turbine rotor turning in response to fluid flow. Here are some advantages of liquid turbine flow meters:

Accuracy: ±0.5%, ±0.2% Optional
Sensor Material: SS304, SS316L Optional
Signal Output: Pulse, 4-20mA, Alarm(optional)
Digital Communication: MODBUS RS485; HART
Power Supply: 24V DC/3.6V Lithium Battery

Nominal diameter: DN15-DN200mm
Accuracy level: ±1%R、±0.5%R、±0.2%R (to be customized)
Instrument type: Field display type, pulse output type, 4-20mA output type, split remote display type
Applicable medium: No impurities, low viscosity, no strong corrosive liquid

Nominal diameter: DN4-DN200mm
Accuracy: ±1%R、±0.5%R、±0.2%R (to be customized)
Instrument type: Field display type, pulse output type, 4-20mA output type, split remote display type
Applicable medium: No impurities, low viscosity, no strong corrosive liquid

A liquid turbine flow meter is a type of flow meter designed to measure the flow rate of liquid substances, such as water, chemicals, or petroleum-based fluids. It operates on the principle of a turbine inserted into the flow stream. As the liquid flows through the meter, it causes the turbine to rotate. The rotational speed of the turbine is directly proportional to the velocity of the liquid, allowing for accurate measurement of the flow rate.

Nominal diameter: DN15-DN200mm
Accuracy： ±1%R、±0.5%R、±0.2%R (to be customized)
Instrument type: Field display type, pulse output type, 4-20mA output type, split remote display type
Applicable medium: No impurities, low viscosity, no strong corrosive liquid

The ATWY threaded liquid turbine flowmeter structure is explosion-proof and can display the total flow rate, instantaneous flow rate and flow full percentage. The battery uses a long-acting lithium battery, the service life of the single-function accumulator battery can reach more than 5 years, and the service life of the multi-function display battery can also reach more than 12 months.

Nominal diameter: DN15-DN200mm
Accuracy： ±1%R、±0.5%R、±0.2%R (to be customized)
Instrument type: Field display type, pulse output type, 4-20mA output type, split remote display type
Applicable medium: No impurities, low viscosity, no strong corrosive liquid

The compact and lightweight design of liquid turbine flowmeters is another defining characteristic. Their relatively simple construction makes them easy to install and maintain. The compact size is particularly advantageous in applications where space constraints are a consideration. The simplicity of their design also reduces the likelihood of clogs or obstructions, contributing to their reliability and minimizing downtime.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Size: DN4,6,10,15,20,32,40,50,65,80
Accuracy: ±0.5% (±0.2% Optional)
Sensor Material: SS304 (SS316L Optional)
Signal Output: Pulse, 4-20mA
Digital Communication: MODBUS RS485, HART

Durability and robustness are inherent characteristics of liquid turbine flowmeters, enabling them to withstand harsh industrial environments. Constructed from materials that resist corrosion and wear, these flowmeters are well-suited for applications involving corrosive liquids, high pressures, and extreme temperatures. This durability ensures a longer operational life and reduces the need for frequent maintenance or replacements.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Liquid turbine flowmeters also find application in the pharmaceutical industry, where precise measurements of liquid flow rates are vital for the production of pharmaceutical products. From monitoring the flow of ingredients during manufacturing to ensuring accurate dosing in pharmaceutical research and development, these flowmeters contribute to the quality and consistency of pharmaceutical processes.

Connection mode：Thread, clamp, flange, clamp type
Accuracy：±1%R、±0.5%R、±0.2%R (to be customized)
Sensor material：304, 316 stainless steel, etc
Use conditions： Medium temperature：-20℃～+120℃  Ambient temperature：-20℃～+60℃
Relative humidity：5%-90%         Atmospheric pressure：86Kpa～106Kpa
Signal output function：Pulse signal, 4-20mA signal
Communication output function：RS485 communication, HART protocol, etc
Working power supply：External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc
Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V
Signal line interface：Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5
Explosion-proof class：Exia II CT or Exd II BT6
Protection class：IP65 or higher customizable

Nominal diameter: DN15-DN200mm
Accuracy level: ±1%R、±0.5%R、±0.2%R (to be customized)
Instrument type: Field display type, pulse output type, 4-20mA output type, split remote display type
Applicable medium: No impurities, low viscosity, no strong corrosive liquid

Turbine flowmeter is a kind of speed instrument, which has the advantages of high precision, good repeatability, simple structure, high pressure resistance, wide measuring range, small size, light weight, small pressure loss, long life, simple operation, easy maintenance, etc., used to measure the volume flow and accumulation of low viscosity, no strong corrosion and clean liquid in closed pipelines. It can be widely used in petroleum, chemical industry, metallurgy, organic liquid, inorganic liquid, liquefied gas, urban gas pipe network, pharmaceutical, food, paper and other industries.

Nominal diameter: DN4-DN200mm
Accuracy: ±1%R、±0.5%R、±0.2%R (to be customized)
Instrument type: Field display type, pulse output type, 4-20mA output type, split remote display type
Applicable medium: No impurities, low viscosity, no strong corrosive liquid

Nominal diameter: DN15-DN200mm
Accuracy level: ±1%R、±0.5%R、±0.2%R (to be customized)
Instrument type: Field display type, pulse output type, 4-20mA output type, split remote display type
Applicable medium: No impurities, low viscosity, no strong corrosive liquid

The threaded liquid turbine flowmeter is a kind of precision flow measuring instrument, which can be used to measure the flow and total amount of liquid with the corresponding flow integrating instrument. Widely used in petroleum, chemical industry, metallurgy, scientific research and other fields of measurement, control system. Threaded liquid turbine flowmeter sensors with sanitary fittings can be used in the pharmaceutical industry.

When selecting a turbine flow meter brand with excellent quality and good reputation, it can be considered from the following aspects: