Home » Flow Meter » Electromagnetic Flow Meter » Digital Water Liquid Pulse 4-20mA RS485 Electromagnetic Flow Meter

Digital Water Liquid Pulse 4-20mA RS485 Electromagnetic Flow Meter

The installation distance between an electromagnetic flowmeter and a control valve, especially a rear valve, is a critical factor that can impact the accuracy and reliability of flow measurements. Here are some general guidelines to help determine the appropriate installation distance:

Rated 4.7/5 based on 337 customer reviews
Share:
Content

Straight Pipe Requirements:

Electromagnetic flowmeters typically require a certain length of straight pipe upstream and downstream for accurate measurements. This straight pipe length helps in achieving a fully developed and stable flow profile. Consult the manufacturer’s guidelines for the specific flowmeter model, as these requirements can vary.

Upstream Straight Pipe Length:

Ensure that there is an adequate length of straight pipe upstream of the electromagnetic flowmeter. This is essential for the flow profile to become well-defined and stable before reaching the flowmeter. The length required may depend on factors such as pipe diameter, fluid characteristics, and flow conditions. A common recommendation is to have at least 5 to 10 diameters of straight pipe upstream of the flowmeter.

Downstream Straight Pipe Length:

Similar to the upstream requirements, downstream straight pipe length is important for maintaining a stable flow profile. The recommended length may be similar to the upstream requirement, typically around 5 to 10 diameters of straight pipe downstream of the flowmeter.

Control Valve Proximity:

Keep the electromagnetic flowmeter at a sufficient distance from any control valve, including rear valves. The presence of control valves can introduce disturbances in the flow profile, and proximity to these valves can affect the accuracy of flow measurements. A general guideline is to maintain a distance of at least 5 to 10 diameters of straight pipe between the flowmeter and any control valve.

Avoid Turbulence:

Ensure that the flow profile in the pipe is free from disturbances and turbulence. Turbulent flow can result from the presence of fittings, bends, or valves, and it can adversely impact measurement accuracy. Installing the flowmeter in a section of the pipe with a smooth and uniform flow is crucial.

Flow Conditioners:

In cases where it is challenging to achieve the required straight pipe lengths, consider using flow conditioners or flow straighteners. These devices can help improve the flow profile and reduce the impact of disturbances caused by fittings or valves.

Inquiry


    More Electromagnetic Flow Meter

    Electromagnetic flowmeter is a speed meter to measure the volume flow of conductive media. While carrying out on-site monitoring and display, it can output standard current signals for recording, adjustment and control, realizing automatic control of detection, and realizing long-distance transmission of signals. It can be widely used in water, chemical, coal, environmental protection, textile, metallurgy, paper and other industries in the flow measurement of conductive liquid. The structure of the instrument has one type and one type.

    Performance Technical parameter
    Size DN3-DN3000mm
    Nominal Pressure 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
    Accuracy +/-0.5%(Standard)     +/-0.3% or +/-0.2%(Optional)
    Liner PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
    Electrode SUS316L, Hastelloy B, Hastelloy C       Titanium, Tantalum, Platinium-iridium
    Structure Type Integral type, remote type, submersible type, ex-proof type
    Medium Temperature -20~+60 degC(Integral type)
    Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
    Remote type(PTFE/PFA/FEP) -10~+160degC
    Ambient Temperature -20~+60deg C
    Ambient Humidity 5-100%RH(relative humidity)
    Measuring Range Max 15m/s
    Conductivity >5us/cm
    Protection Class IP65(Standard); IP68(Optional for remote type)
    Process Connection Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
    Output Signal 4-20mA/Pulse
    Communication RS485(Standard), HART(Optional),GPRS/GSM (Optional)
    Power Supply AC220V (can be used for AC85-250V)
    DC24V (can be used for DC20-36V)
    DC12V (optional), Battery Powered 3.6V (optional)
    Power Consumption <20W Alarm Upper Limit Alarm / Lower Limit Alarm Self-diagnosis Empty Pipe Alarm, Exciting Alarm Explosion Proof ATEX