4-20mA Pulse Output Acid Fluids Batch Control Tri-Clamp Sanitary Concrete Slurry Waste water Stainless Steel Flow Meter

Electromagnetic flow meter, also known as a magmeter, operates on the principle of electromagnetic induction to measure the flow rate of conductive fluids, such as water or other liquids with a certain level of electrical conductivity. Here’s a basic explanation of the principle behind electromagnetic flow meters:

Electromagnetic flowmeters, also known as magmeters, are widely used in various industries for measuring the flow rate of conductive fluids. They operate based on Faraday’s law of electromagnetic induction, where a voltage is induced in a conductor (the fluid) as it moves through a magnetic field. These flowmeters are favored for their accuracy, reliability, and suitability for a wide range of applications. Here are different categories of electromagnetic flowmeters and their fields of application:

Electromagnetic flowmeters are used to measure the volume flow of industrial liquids and there are many media in industrial liquids, electromagnetic flowmeters are often used to measure the flow of conductive media.

Four physical cleaning methods of electromagnetic flowmeter electrode

Electromagnetic flow meters offer several advantages, making them a popular choice in various industrial applications. Here are some of the key advantages of electromagnetic flow meters:

Calibration checks are another essential component of fault diagnosis for electromagnetic flow meters. Regular calibration against known standards ensures that the meter’s measurements remain accurate over time. Any deviation from the expected calibration values may indicate sensor degradation, electronic component failure, or other issues that require attention.

Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

According to the principle formula of the electromagnetic flowmeter, the induced signal potential is not affected by the change of conductivity and temperature, pressure, density and viscosity when the liquid conductivity is uniform. However, in the actual measurement, due to the following reasons, the electrical conductivity will also have some impact on the measurement.

The choice of water flow meter is a comprehensive consideration process, involving many aspects of factors. Here is a guide to tap water flow meter selection to help you choose the most suitable solution:

The application of flowmeter in food processing is very extensive, mainly reflected in the following aspects:

The versatility of electromagnetic flowmeters is a testament to their robust performance across a wide range of conductive liquids. Whether dealing with water, acids, bases, or slurries, these flowmeters maintain their accuracy and reliability. This adaptability is particularly valuable in industries with varying fluid compositions, allowing for a single flowmeter type to be employed in diverse applications without sacrificing performance.

Protection Class: IP65(Standard); IP68(Optional for remote type)
Process Connection: Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal: 4-20mA/Pulse
Communication: RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply: AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption: <20W Alarm: Upper Limit Alarm / Lower Limit Alarm Self-diagnosis: Empty Pipe Alarm, Exciting Alarm Explosion Proof: ATEX

With the speeding up of urbanization process in our country, environmental pollution is increasingly serious. Because in sewage treatment, it is necessary to analyze and control the discharged sewage, additives, sludge, etc., so the flow measurement is very important. Among the many flowmeter products used for sewage measurement, electromagnetic flowmeter measurement accuracy is higher.

The scale of the water supply system itself is huge, and the environment in which it is located is complex and changeable, requiring the electromagnetic flowmeter to have strong stability and reliability, so in the actual use process, the matters needing attention should be clear.

Electromagnetic flowmeters are classified according to the assembly method of converters and sensors, with split type and one type. Split type electromagnetic flowmeter is relative to the integrated, its components are: measuring tube, electrode, excitation coil, iron core and yoke housing. Used to measure the volume flow of conductive liquid and slurry in closed pipes.

What are the external interference problems of the electromagnetic flowmeter for domestic wastewater

In the metering industry, electromagnetic flowmeter is a basic metering tool, and its range of use is very wide. The emergence of electromagnetic flowmeters has made great contributions to many industries, and it occupies a very important position in these industries. Pay more attention when using the electromagnetic flowmeter, check it before use to see how accurate its measurement is. The calibration of electromagnetic flowmeter is mainly considered from the following aspects:

Electromagnetic flowmeters, commonly known as magmeters, are a sophisticated and versatile type of flow measurement device widely used in industrial applications. Unlike traditional mechanical flow meters, electromagnetic flowmeters operate on the principle of electromagnetic induction to provide highly accurate and reliable measurements of liquid flow. The technology behind these devices makes them suitable for a diverse range of industries where precise flow measurement is crucial for various processes.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type

In the flow measurement of domestic sewage, it is very important to choose the right flowmeter to ensure the accuracy and reliability of the measurement results. Here are some suggestions to help you choose the right flowmeter for domestic sewage:

Electromagnetic flowmeter at work requires that the measured medium must be ground potential, generally through the pipeline or flange ground, if the process pipe connected to the sensor relative to the measured medium is insulated (plastic pipe or pipe with an insulating lining), you must choose a grounding ring or sensor with a grounding electrode, so that the measured medium in the ground potential, easy to be ignored in the actual design and installation.

The measuring principle of intelligent electromagnetic flowmeter is Faraday’s law of electromagnetic induction, which measures the flow of conductive fluid according to the electromotive force induced by the conductive fluid through the external magnetic field. The main components of the sensor are: measuring tube, electrode, excitation coil, iron core and yoke shell.

Electromagnetic flow meters, also known as magmeters, are advanced devices used for measuring the flow rate of conductive fluids such as water and slurries. These meters operate based on the principles of electromagnetic induction. A magnetic field is generated by the meter’s coils, and as the conductive fluid flows through the meter’s pipe, it generates a voltage proportional to the flow rate. The strength of this induced voltage is directly correlated with the speed of the fluid, allowing for accurate and reliable flow measurements.

The grounding ring is a crucial component in the installation of an electromagnetic flowmeter as it helps establish proper grounding and ensures accurate and reliable measurements. Here’s a general guide on how to install an electromagnetic flowmeter grounding ring:

Electromagnetic flowmeter in the industry has achieved good results, then as the core accessories of electromagnetic flowmeter – electrode, electrode is contact with the measured medium more accessories, then the cleaning details of the electrode is a crucial point, of course, also pay attention to a certain method.

The correct selection of electromagnetic flowmeter is the prerequisite to ensure the normal use of the instrument. The diameter, flow range, lining material, electrode material and output current of the electromagnetic flowmeter should be determined according to the physical and chemical properties of the measured flow medium, and can adapt to the field environment and meet the technical indicators and performance requirements.

In the field of industrial processes, electromagnetic flowmeters are extensively employed for measuring the flow of liquids such as chemicals, acids, and slurries. Their capability to handle corrosive fluids and resist wear makes them invaluable in industries like chemical manufacturing, pharmaceuticals, and food and beverage production. In these applications, electromagnetic flowmeters contribute to process optimization, ensuring precise control of fluid volumes and enhancing overall operational efficiency.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range： Max 15m/s
Conductivity： >5us/cm

For the daily inspection of the electromagnetic flow meter, in addition to the inspection of the sensor we talked about last time, it is also necessary to check the sensor of the electromagnetic flow meter, connecting cables, etc., below we will understand how to operate.

Intelligent electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including acid, alkali, salt and other highly corrosive liquids.

Basic fault treatment of intelligent sewage electromagnetic flowmeter:

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

The material of construction is also a vital aspect in electromagnetic flowmeter selection. Different applications may require flowmeters made from specific materials to withstand corrosive environments or harsh chemicals. Ensuring that the materials of construction are compatible with the fluid and environmental conditions helps enhance the longevity and reliability of the flowmeter.

Another critical factor to consider is the flow rate range of the application. Electromagnetic flowmeters exhibit excellent accuracy and stability across a broad range of flow rates, making them suitable for both low-flow and high-flow applications. It is essential to match the flowmeter’s specifications, such as its minimum and maximum flow rates, with the expected flow conditions in the system.

Measuring Range： Max 15m/s
Conductivity： >5us/cm
Protection Class： IP65(Standard); IP68(Optional for remote type)
Process Connection： Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal： 4-20mA/Pulse
Communication： RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply： AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption： <20W Alarm： Upper Limit Alarm / Lower Limit Alarm Self-diagnosis： Empty Pipe Alarm, Exciting Alarm Explosion Proof： ATEX

Several factors can contribute to the inaccurate measurement of flow by electromagnetic flowmeters. These factors can vary depending on the specific application, installation conditions, and characteristics of the fluid being measured. Here are some common reasons for inaccurate flow measurement with electromagnetic flowmeters: